Manual

Controller 4X

Safety

Kitesurfing is an awesome new sport that can be enjoyed by anybody. With adventure sports there is an element of danger which can cause harm or death so all Safety Warnings must be followed.

Get Educated

Before attempting to kitesurf we recommend you get lessons from a qualified kitesurf instructor.
Kitesurfing SchoolsSwitch Kiteboarding Link Thumb

Videos are an excellent way to help  brush up on your skills. There are a number of excellent dvd's available.
Kitesurfing Instructional dvd'sSwitch Kiteboarding Link Thumb
Youtube is also an excellent resource to learn some skills.
Kitesurfing Instructional Youtube videosSwitch Kiteboarding Link Thumb

Learn more important safety tips from these great websites.

Kite with Friends

Kitesurfing with friends is always more fun and alot safer.

WARNING!

KITE FLYING CAN BE DANGEROUS – Read these instructions before Inflating. By using this product the user fully understands the inherent hazards and dangers that may lead to serious injuries or death.
- Never use near power lines, airports, streets, rocks, trees, houses, vehicles, including boats, bystanders or any other structure.
- Observe the weather conditions and do not use this product in thunderstorms, offshore, overly strong or gusty winds.
- For adult use only. Learn how to fly competently before using this product.
- This product is not a floatation or flying device and should not be used as one.
- Always wear safety equipment such as helmet and when using in water, a personal floatation device.
- Always allow the kite to dry before storage. Do not overinflate and have any damage repaired immediately by a qualified repair facility.

Quick Release

Before using the control bar you MUST fully understand how the quick release works and are confident in releasing and re-engaging the quick release system. We recommend releasing and re-engaging the safety release at least 6 times to familiarize yourself.

Swivel

Simply spin the swivel in the reversed direction the lines are twisted in. It is important to keep your lines twist free to ensure the kite flags freely.

Trim Handle

Simply grab and pull. If you have your kite fully trimmed, open the velcro loop and close around the depower rope so it does not dangle and get tangled.

Cleat

Simple cleat system. Push in to engage and pull out to disengage.

Loop Stick

Hook your harness hook to the loop then push your loop stick into the harness hook under the loop. To disengage reverse this process.

Mini Kite Leash

Simple push away releases and easy re-engage. Connect the mini kite lease to your harness in an easy to reach place for easy access.

Flag Your Kite

Ensure you have adequate clear space downwind of you. Release your Quick Release and the kite will simply fall to the ground. The kite may flip around a little before coming to a complete rest.

High Split

Some kites are tuned to perform best with a high front line split. To uses the high split simply attach the loop ring to the high connection point and thread the opposite front line through the ring.

If you are using the control bar at the standard split setting simply remove the high split loop ring.

Remove high split

Connect your 5th line

The simplest way to connect your 5th line is to thread the 5th line around the center part of the Trim Bracket and pull tight.

Connetc 5th line

Rear pigtail extensions

If you need to calibrate your rear lines follow these simple instructions to install your Rear Pigtail Extensions.

1 - 2 rear line pigtails and 2 rear pigtail extensions
2 - Remove the pigtail from the flying line
3 - Thread flying line through the large loop on the extension
4 - Thread the extension through the loop on the flying line
5 - Pull the extension all the way through the loop on the flying line
6 - Thread the pigtail through the top loop on the extension
7 - Thread the pigtail back through its own loop
8 - Pull pigtail tight and repeat on the other line
9 - Extensions length can be adjusted by simply moving the knot.

Rear Pigtail Extensions

Customise your loop size

Some riders like to use a small loop. If you want to customise your loop follow these simple insructions:

1- Tools needed: phillips head screwdriver, Sharp knife, Drill with small drill bit (2mm)
2 - Remove the 2 screws holding in the loop
3 - Pull loop out and cut to length
4 - Drill 2 pilot holes. Make sure the holes go through the center of the rope
5 - Fasten screws back into base ensuring the screw went into the pilot holes
6 - Its recommended not to make your loop too small

Shorten your loop
LiveZilla Live Chat Software